Honda Accord: Operating the XM Radio - Playing the XM Radio (EX-L, Canadian EX, and all V6 models without 
navigation system) - Features - Honda Accord 2008-2012 Owner's ManualHonda Accord: Operating the XM Radio

To listen to XM Radio, turn the ignition switch to the ACCESSORY (I) or ON (II) position, and press the last channel you button. The last channel you listened to will show in the display.

Adjust the volume by turning the power/volume knob.

MODE - To switch between channel mode and category mode, press and hold the TITLE button until the mode changes.

In the channel mode, you can select all of the available channels. In the category mode, such as Jazz, Rock, Classical, etc., you can select all of the channels within that category.

Each time you press and release the TITLE button, the display changes in the following sequence: name, title, and category.

You can also change the mode from the menu items. Press the MENU button to display the menu items, then turn the selector knob to select MODE/CATEGORY and press the selector knob (ENTER). Each time you press and release the selector knob (ENTER), the display changes between CHANNEL and CATEGORY. To enter the setting, press the TITLE button.

You may experience periods when XM Radio does not transmit the artist’s name and song title information. If this happens, there is nothing wrong with your system.

TUNE - Turn the selector knob to change channel selections. Turn the knob right for higher numbered channels and left for lower numbered channels. In the category mode, you can only select channels within that category.

You can also select a channel or

You can also select a channel or category from the list by using the selector knob. Push the selector knob (ENTER) to switch the display to the list displayed with three segments, then turn the knob to select a channel or category. Press the selector knob (ENTER) to set your selection.

 CATEGORY () - Press or either side of the CATEGORY bar to) - Press either side of the CATEGORY bar to select another category.

SCAN - The SCAN function gives you a sampling of all channels while in the channel mode. In the category mode, only the stations within that category are scanned. To activate scan, press the SCAN button. The system plays each channel in numerical order for a few seconds, then selects the next channel. When you hear a channel you want to continue listening to, press the button again.

Preset - You can store up to 12 preset channels using the six preset buttons. Each button stores one channel from the XM1 band and one channel from the XM2 band.

To store a channel:

1. Press the XM1 or XM2 will show in the button. Either XM1 or XM2 will show in the display.

2. Use the selector knob, or the CATEGORY bar or SCANbutton to tune to a desired channel.

In category mode, only channels within that category can be selected.

In channel mode, all channels can be selected.

3. Pick the preset button you want for that channel. Press and hold the button until you hear a beep.

4. Repeat steps 2 and 3 to store the first six channels.

5. Press the XM button again. The other XM band will show. Store the next six channels using steps 2 and 3.

Once a channel is stored, simply press and release the proper preset button to tune to it.

    Playing the XM Radio (EX-L, Canadian EX, and all V6 models without navigation system)
    Playing the XM Radio (EX-L, Canadian EX, and all V6 models without navigation system) Your vehicle is capable of receiving XM Radio anywhere in the United States and Canada, except Hawaii, ...

    XM Radio Display Messages
    ‘‘LOADING’’ - XM is loading the audio or program information. ‘‘OFF AIR’’ - The channel currently selected is no longer broadcasting. ‘‘UPDATING’’ - The encryption code ...

    See also:

    Windshield Washers
    Check the level in the windshield washer reservoir at least monthly during normal use. Check the fluid level by removing the cap and looking at the level gauge. On Canadian models: The low ...

    Outside Temperature Indicator
    If equipped This indicator displays the outside temperature in Fahrenheit (U.S. models) or Celsius (Canadian models). To see the outside temperature, press and release the select/reset knob ...

    VTC Oil Control Solenoid Valve Removal/Test/lnstallation
    1 Disconnect the VTC oil control solenoid valve 2P connector (A). 2. Remove the bolt (B) and the VTC oil control solenoid valve (C). 3. Connect VTC oil control valve 2P connector terminal No. ...