Honda Accord: SRS Unit Replacement
Removal
1. Do t h e b a t t e r y t e r m i n a l d i s c o n n e c t i o n procedure (see page 22-91), t h e n w a i t at least 3 m i n u t e s before s t a r t i n g work.
2. Remove t h e d r i v e r ' s a n d passenger's dashboard center l o w e r cover (see page 20-170).
3. Remove t h e TORX bolt (A) u s i n g a TORX T30 bit.
4. Remove t h e a u d i o disc changer ( w i t h navigation system) (see page 23-118) or center pocket (without n a v i g a t i o n system) (see page 20-168).
5. Disconnect SRS u n i t connectors A (39P) a n d B (39P) f r o m t h e SRS unit (C).
NOTE: T h e SRS u n i t connectors have lever locks.
Release t h e locks before d i s c o n n e c t i n g t he connectors (see page 24-30).
6. Remove t h e TORX bolts (D) u s i n g a TORX T30 bit, then pull out the SRS unit.
Installation
1. Install t h e SRS u n i t (A) w i t h a n e w TORX bolt (B),using a TORX T30 bit.
NOTE: Be s u r e t h e SRS u n i t is s i t t i ng squarely against it's bracket before torquing the TORX bolt.
2. Install t h e n e w TORX bolts (A) u s i n g a TORX T30 b i t t h e n connect t h e connectors (B) t o t h e SRS unit (C); push t h em i n t o p o s i t i on until t h e y click (see page 24-30).
3. Do t he battery terminal reconnection procedure (see page 22-91).
4. Make sure t h e SRS unit has t h e latest software. If it does not have t h e latest, update t h e software in t he SRS unit (see page 24-39).
5. Do t he ODS unit initialization (see page 24-40).
6. Check t he o p e r a t i o n of t h e ODS u n i t w i t h t h e HDS (see page 24-41).
7. C o n f i rm proper SRS o p e r a t i o n : T u r n t h e i g n i t i on switch t o ON (II); t h e SRS indicator s h o u l d c o m e on f o r about 6 seconds and t h e n g o off.
8. Reinstall all removed parts.
Cable Reel Replacement
Removal 1. Make sure t h e f r o n t w h e e l s are a l i g n e d straight ahead. 2. Do t h e b a t t e r y t e r m i n a l d i s c o n n e c t i o n procedure (see page 22-91), t h e n w a i ...Side Impact Sensor (First) Replacement
4-Door Removal 1. Do t h e battery t e r m i n a l d i s c o n n e c t i o n procedure (see page 22-91), t h e n w a i t at least 3 m i n u t e s before s t a r t i ng work. 2. Remove t h e B-p ...See also:
System Description
fuel and Emissions S f stems Diagram
1.AIR FUEL RATIO (A/F) SENSOR (SENSOR 1)
2.SECONDARY HEATED OXYGEN SENSOR
(SECONDARY H02S) (SENSOR 2)
3.MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR
4.ENGINE COO ...
Control Unit Input
Test/Replacement
1. Remove the driver's dashboard lower cover (see page 20-166).
2. Remove the screws, then disconnect the 28P connector (A) from the
HandsFreeLink control unit (B).
3. Inspect the connector an ...
Refrigerant Leak Check
Special Tools Required
• Leak Detector YGK-H-10PM*
• Leak Detector HLD-100*
• Leak Detector TIFZX-1*
• OPTIMAX Jr. A/C Leak Detection Kit TRP124893*
*Available through the Hon ...