Honda Accord: Speaker Test/Replacement - Audio System - Audio, Navigation, and Telematics - Honda Accord MK8 2008-2012 Service ManualHonda Accord: Speaker Test/Replacement

Front Door Speaker

1. Remove the door panel.

• 4-door (see page 20-17) • 2-door (see page 20-12) 2. Remove t h e bolt (A). Then lift the speaker straight up to release t h e lower clips (B).

If you pull the speaker out too far from the door, you


If you pull the speaker out too far from the door, you will damage the lower clips.

3. Disconnect the 2P connector (C), and remove the


3. Disconnect the 2P connector (C), and remove the speaker.

4. Measure the resistance between the terminals No. 1 and No. 2. There should be about 4 O.

5. Ifthe resistance is not as specified, replace the door speaker.

Front Door Tweeter (With Premium Audio System)

1. Detach the clip (A) and remove the front door tweeter - cover (B). Then disconnect the connector (C).

2 . Measure the resistance between the front door


2 . Measure the resistance between the front door tweeter 2 P connector terminals No. 1 and No. 2 . There should be about 3.3.


3. If the resistance is not as specified, replace the front


3. If the resistance is not as specified, replace the front door tweeter. Remove the front door tweeter (A) from front door tweeter cover (B).

Front Door Tweeter (Without Premium Audio


Front Door Tweeter (Without Premium Audio System)

1. Detach the clip (A) and remove the front door tweeter cover (B). Then disconnect the connector (C).

2. Remove the front door tweeter (A) from the front


2. Remove the front door tweeter (A) from the front tweeter cover (B).

3. Check the capacitor condition. If any malfunction is


3. Check the capacitor condition. If any malfunction is found, replace the front door tweeter.

4. Measure the resistance between the front door tweeter (A) terminal No. 2 and the outside terminal of the capacitor. There should be about 4.
.

5. If the resistance is not as specified, replace the front


5. If the resistance is not as specified, replace the front door tweeter.

Rear Speaker

1. Remove t h e rear shelf (see page 20-128).

2. Remove t h e mounting bolt (A), then tilt the speaker forward to release the front clips (B).

If you pull the speaker out t o o far from the rear


If you pull the speaker out t o o far from the rear bulkhead, you w i l l damage the lower clips.

3. Disconnect the 2P connector (C), and remove the rear


3. Disconnect the 2P connector (C), and remove the rear speaker.

4. Measure the resistance between the terminals No. 1 and No. 2. There should be about 45. If the resistance is not as specified, replace the rear.


5. If the resistance is not as specified, replace the rear speaker.

Subwoofer

1. Remove the rear shelf (see page 20-128).

2. Remove the four mounting bolts (A) from the subwoofer (B).

3. Disconnect the 2P connector (C), and remove the


3. Disconnect the 2P connector (C), and remove the subwoofer.

4. Measure the resistance between the terminals No. 1 and No. 2. There should be about 2 O.

5. If the resistance is not as specified, replace the subwoofer.

    Crossover Network Control Unit Removal/Installation
    Driver's Door Speaker Crossover Network Control Unit 1. Remove the driver's dashboard lower cover (see page 20-166). 2. Disconnect the connector (A), then remove the driver's door speaker cross ...

    Audio Remote Switch Test
    1. Remove the steering wheel (see page 17-6). 2. Remove the audio remote switch (see page 17-7). 3. Measure the resistance between the terminals No. 1 and No. 8 in each switch position accordin ...

    See also:

    Security System Alarm
    The security system alarm activates when the doors, trunk, or hood are opened without the key, remote transmitter, or smart entry system. The security alarm continues for a maximum of two minutes ...

    Throttle Body Disassembly/Reassembly
    ...

    Disc Repeat
    To replay the current disc continuously, select DISC REPEAT, and press ENTER on the interface selector. As a reminder, you will see REPEAT next to DISC on the screen. To turn this feature off ...