Honda Accord: MICU Input Test - Wipers/Washers - Body Electrical - Honda Accord MK8 2008-2012 Service ManualHonda Accord: MICU Input Test

NOTE; Before testing, troubleshoot the multiplex integrated control unit first, using B-CAN System Diagnosis Test Mode A (see page 22-134).

Drivers MICU

1. Turn the ignition switch to LOCK (0), and remove the driver's dashboard lower cover (see page 20-166).

2. Disconnect driver's under-dash fuse/relay box connectors F, Q, and R.

NOTE; AH connector views are wire side of female terminals.

CONNECTOR F (33P)

CONNECTOR Q (20P)


CONNECTOR Q (20P)

CONNECTOR R (24P)


CONNECTOR R (24P)

*: A/T


*: A/T

3. Inspect the connector and socket terminals to be sure they are all making good contact.

• If the terminals are bent, loose or corroded, repair them as necessary and recheck the system.

• If the terminals look OK, go to step 4.

4. With the connectors still disconnected, do these input tests at the following connectors.

• If any test indicates a problem, find and correct the cause, then recheck the system.

• If all the input tests prove OK, go to step 5.

5. Reconnect the connectors to the driver's under-dash fuse/relay box, turn


5. Reconnect the connectors to the driver's under-dash fuse/relay box, turn the ignition switch to ON ( I I ) , and do these input tests at the following connectors.

• If any test indicates a problem, find and correct the cause, then recheck the system.

• If all the input tests prove OK, goto step 6.

Passenger's MICU


Passenger's MICU

6. Turn the ignition switch to LOCK (0), and remove the passenger's kick panel.

• 2-door (see page 20-105) • 4-door (see page 20-107)

7. Disconnect passenger's under-dash fuse/relay box connectors A, E, G# 1 and H*2.

*1: LX, LX PZEV, LX-P, LX-P PZEV

*2: Except LX, LX PZEV, LX-P, LX-P PZEV

NOTE: AH connector views are wire side of female terminals.

CONNECTOR A (33P)

CONNECTOR E (18P)


CONNECTOR E (18P)

CONNECTOR G(16P)


CONNECTOR G(16P) (LX, LX PZEV, LX-P, LX-P PZEV)

CONNECTOR H (38P)


CONNECTOR H (38P) (Except LX, LX PZEV, LX-P)

*: '08-09 models


*: '08-09 models

8. With the connectors still disconnected, make these input tests at the connectors.

• If any test indicates a problem, find and correct the cause, then recheck the system.

• If all the input tests prove OK, go to step 9.

9. Reconnect the connectors to the passenger's under-dash fuse/relay box, and


9. Reconnect the connectors to the passenger's under-dash fuse/relay box, and do these input tests at the following connectors.

• If any test indicates a problem, find and correct the cause, then recheck the system.

• If all the input tests prove OK, Go to step 10.

* 1 : '08-09 models


* 1 : '08-09 models

*2: LX, LX PZEV, LX-P, LX-P PZEV

*3: Except LX, LX PZEV, LX-P, LX-P PZEV

10. If multiple failures are found on more than one control unit, replace the driver's under-dash fuse/relay box (includes the driver's MICU).

• USA models (see page 22-86) • Canada models (see page 22-87) If input failures are related to a particular control unit, replace the control unit.

    DTC Troubleshooting
    DTC B1077: Windshield Wiper Auto-stop (AS) Signal Circuit Malfunction NOTE: If you are troubleshooting multiple DTCs, be sure to follow the instructions in B-CAN System Diagnosis Test Mode A (see ...

    WiperA/Vasher Switch Test / Replacemen
    1. Remove the steering column covers {see page 20-181). 2. Disconnect the dashboard wire harness 8P connector (A) from the wiper/washer switch (B). 3. Remove the two screws, then slide out the ...

    See also:

    Braking System
    Your vehicle is equipped with disc brakes at all four wheels. A power assist helps reduce the effort needed on the brake pedal. The emergency brake assist system increases the stopping force ...

    Paint Code
    ...

    Keys and Locks
    The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver’s door lock. You can keep the trunk release handle, and glove box locked when y ...